BRIOT ACCURA MANUAL PDF

briot accura cx manual PDF ePub Mobi. Download briot accura cx manual PDF, ePub, Mobi. Books briot accura cx manual PDF, ePub, Mobi. Page 1. Briot Accura Maintenance Manual Sap Pm End User Manual Calibration Process. Sap Pm End User Manual Calibration Process. PDF or Read Edger Manual For Briot Accura PDF on The Most Popular Online PDFLAB. Get Access Edger Manual For Briot AccuraPDF and Download Edger .

Author: Fele Dairan
Country: Lithuania
Language: English (Spanish)
Genre: Music
Published (Last): 24 May 2013
Pages: 280
PDF File Size: 20.97 Mb
ePub File Size: 3.92 Mb
ISBN: 303-9-75175-946-9
Downloads: 56640
Price: Free* [*Free Regsitration Required]
Uploader: Tolabar

We appreciate and thank you for the confidence you have entrusted in our name. This Edger has been manufactured with the greatest of care and inspected to meet the most rigorous Briot standards.

We recommend you read this manual, carefully, for the proper use and enhancement of the life of your new equipment. Please, keep it in a safe place for future reference. As with all mechanical and electronic devices, however, your Briot machine will require periodic adjustments, routine maintenance, and eventually the replacement of certain hard-working parts.

To ensure that your Briot unit is continually operating at peak efficiency, it will be beneficial to have your unit periodically inspected by an authorised Briot service representative. Once again, accira you for choosing Briot.

Briot Accura Calibration Manual

The information cacura in this manual are not contractual and can be modified without notice. On top of that, errors and omissions can occur, although all is performed to avoid them.

Briot does manuxl assume any responsibilities or liabilities biot damages caused by errors or omissions. A-3 Cleaning the Pump Recirculating System B-3 Memory Extension Circuit Board B-4 Communication Extension Circuit Board B-9 Appendix C Specifications Specifications: Procedure Follow the steps below to unpack your edger unit. Step Action 1 Remove the nose piece from the wedge inserted into the scanform.

Check the set screw of the gear A is lined up with the hole. If not, turn the gear in order to get to this situation. Do not place the edger near or on top of a source of energy radiator or heater. Make sure your voltage source corresponds to the voltage specified on edger nameplate, located on the rear of the machine. If the machine is not going to be used for a long period of time you should unplug the power cords from the wall outlet.

Briot does not assume any responsibilities or liabilities for damages caused by negligence or ignoring the safety precautions enlisted in this manual. The bench The bench receiving the machine must steady and leveled and be made up of a foot print of about x mm.

Briot Accura Color Lens Edger Users Manual |

This faucet must be kept for the machine and drilled at 80 cm maximum from the place excepted for the machine. The access must be easy and the faucet must be turn off when the machine is not used. For a well functioning of the machine, the maximum water supply pressure must be between 4 and 7 bar. The pump Briot supplies pump system especially made for required water supply to Accura and for filtering of the edging waste.

  FISIOPATOLOGIA DE LA DISMENORREA PDF

The pump dimensions are as follows: Step 1 Action Drill the bench as follows. Installation Follow the steps below to install the machine. Step Action 1 Level the machine by screwing or unscrewing the four feet.

Manula refers to Appendix A for pump installation important notice. In case of installation on direct water only, add a filter joint manial in the accessory box. Connect the inverter control cable to the mannual. Connect the inverter power cable to the edger. Fix the cable strain relief to secure the motor cable.

OMA Network Connector 8 Mount the chucks and the centring nose piece scanform contained in the accessory box. Must be adjusted as follows: Description The following table describes each key of the keypad. Confirms the numerical value entered. Decrements the selected numerical value. Increments the selected numerical value. Releases and clamp the lens. Press and hold the key to clamp. This key exists also to the left of the edging station, for left-handed accira.

In combination with the following key: Does an emergency stop. Unmarked key Fct0 to Fct5its meaning depends of the parameter msnual to the left of this key.

Unmarked key Fct6 to Fct9its meaning depends of the parameter displayed facing this key. Key Description Cacura and clamping the lens. Key established on this keyboard to be more accessible by left-handed people.

Briot Accura Calibration Manual

Setting and adjusting use only. ON Displays the message ON during regular operation. Interruption of Frame Shape Scanning. This key is linked with a green LED allowing to attract your attention to the necessity to press on this key xccura execute the shape scanning cycle. Allows to enter the following parameters: The screens scroll in the following order: Description Manula following table describes each scanning screen function of the Accura.

Step 1 Action Create a job number.

To do this, press the keypad and press the key or enter a job number aid of the key. Check the eyewire joint is well closed tighten the joint screw. When the scanning is finished, the shape is drawing on the screen. Step Action 1 Press the Result: The scanning is stopped and the following message comes up.

Tracing aborted Ok Fct8 2 Press the Fct8 key. The message disappears from the screen. You can resume the scanning again. To do this, follow the steps below. If you scan… Then… Left side 1.

Insert the pattern placing the nasal part brit the right or insert the acucra demonstration lens onto the pattern holder. Insert the pattern placing the nasal part to the left or insert the left demonstration lens onto the pattern holder.

  DUTILLEUX TOUT UN MONDE LOINTAIN PDF

Pattern holder 4 Select brilt symmetry function. The machine interprets automatically the entered value as bridge or frame distance. The height is measured from where the pupil vertically aligns to the edge of the lens at the lower half of the frame Fct5 28 Fct6 Segment width Optical center: Lens is laid out and blocked on the optical center Geometrical center: The optical center is displaced from the mechanical center Fct7 BOX decentration: Height calculated from the optical center to the extreme bottom point of the frame MIX decentration: Step Action 1 Select the right or left lens to layout.

The machine interprets automatically the entered value as a total pupil distance, monocular pupil distance or a decentration. You can use the blocks up to times. Any use beyond this limit could lead to axis or distance problems whose Briot briof all responsibilities. In case of thin or high cylinder lenses, place the lens holder ring contained in accessory box between the screen and the lens to hold and avoid it to break or move. Fct4 Grooving is not allowed on mineral lens.

The bevel is placed in the center of the lens Rear Side Bevel: The bevel is placed on the rear side of the lens Operator Bevel Hand Symbol: The operator see Controlled Bevel below places the bevel Esthetical bevel: The lens size is also adapted to the possible frame bending before lens fitting.

Lens circumference and eye wire circumference are accuea Expert bevel: Automatic bevel ; the machine uses the frame curve to mankal the bevel and position it as much as possible to the front surface of the lens.

Briot Accura Color Lens Edger Users Manual

Lens fitting without frame bending Expert single groove: Automatic lens grooving — 0. Lens Final Size Safety-bevel: Edging Fragile Lens for example Hydrophobic lenses: Step 1 Action Call a job aid of the bar code reader or entering manually the number aid of the keypad and press the Result: The shape appears accur the screen with its edging parameters. Place the lens to edge in the edger, already centered and blocked, as follows.

Place the blocked lens into the left side adaptor. The use of the 19mm adapters when the 17mm ones are required will make a collision of the adapter with the wheels!

The visor closes automatically and the edging cycle starts in the following order: