Split Tear Strength – ASTM D The force per unit thickness required to tear a material. Test specimens are placed in a tensile test machine. The jaws are set. This standard is issued under the fixed designation D ; the number 1 These test methods are under the jurisdiction of ASTM Committee D-9 on. Electrical. ASTM D Standard Test Methods for Crosslinked Insulations and Jackets for Wire and Cable.

Author: Meztigul Mazurisar
Country: United Arab Emirates
Language: English (Spanish)
Genre: Science
Published (Last): 18 March 2014
Pages: 483
PDF File Size: 5.38 Mb
ePub File Size: 20.69 Mb
ISBN: 611-4-93137-955-8
Downloads: 67232
Price: Free* [*Free Regsitration Required]
Uploader: Ararr

A number in parentheses indicates the year of last reapproval. When d40 full cross section is used, the specimens shall not be cut longitudinally. Remove the weighing tube, pour the solution into a beaker, wash the weighing tube held over the beaker with distilled water, pour the solution from the beaker into a volumetric? Physical Test Procedures Measure the diameter of the uninsulated conductor also, and calculate the original thickness of the insulation, T1 asym follows: Failure of either of the retests indicates nonconformity of the sample to the requirement speci?

Determine the tensile strength and elongation at the same wstm that the original properties are determined see Section Make an effort to separate the jacket from the insulation by slitting the covering through to the conductor and pulling the jacket and insulation apart by pliers.

These test methods do not apply to the class of products known as?

ASTM D – 13 Standard Test Methods for Crosslinked Insulations and Jackets for Wire and Cable

Failure occurs when an arc is maintained for two successive cycles between the electrode and solution across 1. Designate the insulation area in square inches or square millimetres of a in. Control the temperature by keeping zstm apparatus in an air-conditioned room or by partially immersing the chamber in a water bath, either connected to a d70 water system or provided with thermostatically controlled electric heaters.


Jackets with a thickness of less than 0.

D — 05? It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. S470 the upper half of each specimen.

In series with this is a second drier containing anhydrous calcium chloride or anhydrous calcium sulfate, and a U-tube hygrometer containing a small quantity of anhydrous copper sulfate which is used as an indicator of moisture.

Release the test specimen within 5 s, and determine the distance between bench marks 1 min after the beginning of release.

Equip the buffing apparatus wstm a cylindrical table arranged so that it can be advanced very gradually. The tank has a tightly? Solidly ground all electrically conductive parts that any person might come in contact with during the test.

Remove the dust for approximately a 0. See Test Methods D for a more complete discussion of the signi? The percentage of mineral? If the jacket cannot be removed, prepare specimens by buffing. Discharge from the test chamber is accomplished by a double cock arrangement, one acting as a direct discharge into the outside atmosphere and the other, when normally closed, acting as a bypass test-cock. Give each value to the nearest 0. Adjust the height of the? It is also possible to facilitate the removal of the insulation by stretching the conductor to the breaking point in a tensile-strength machine.

We use cookies to make our website easier to use and to better understand your needs. Age specimens having astn tape applied prior to crosslinking with such tape removed.

ASTM D470 – 13

Determining Temperature Coefficients for Insulation Resistance See Test Method D Cable Outside Diameter Less than 1? Do not include the thickness of any separator in the thickness of insulation. Electrical Tests of Insulation. Ozone resistance tests provide useful data for research and development, engineering design, quality control, and acceptance or rejection under speci?

  HDX 8006 PDF

This permits easy access to the interior and also the inspection of specimens, without opening the chamber during test. Thermal tests provide useful data for research and development, engineering design, quality control, and acceptance or rejection under speci?

ASTM D — While the initial values are important, changes in capacitance and dissipation factor with aging and absorption of moisture in service are usually much more signi? Calculate the strength of the Na2S2O3 solution in accordance with Rate of Voltage Application Therefore, tests are done on insulated or jacketed wire or cable in these test d740 solely to determine the relevant property of the insulation or jacket and not to test the conductor or completed cable.

D4700 this potential continuously for at ast, 6 h. After generating the ozone for at least 15 min, make aetm check on the percentage of ozone concentration see Some materials are more susceptible to such discharge damage than others. The micrometer and microscope shall be capable of making measurements accurate to at least 0.

Apply a to V dc potential between the two electrodes. This solution is stable for a week if kept in a cool, dark place in a well-stoppered, brown bottle. The gross length of each specimen shall r470 13 ft 3.